# Powder Metallurgy Press and Sinter Cost Per Part: How to Estimate It > Source: https://netray.co/resources/powder-metallurgy-press-and-sinter-cost-per-part > Publisher: Netray (netray.co), AI and integration engineering for ERP and manufacturing systems. > Section: Knowledge Base ## Short answer Estimate powder metallurgy cost per part: powder grade, press tonnage and strokes per minute, die tooling, belt furnace sintering, sizing and secondary operations. ## Category erp-general ## Content **Intro:** Powder metallurgy cost per part is powder weight times material price, plus press time set by strokes per minute and parts per stroke, plus sintering belt furnace cost by weight throughput, plus tooling amortization and any sizing, machining, impregnation or heat treatment. PM suits high-volume structural parts such as gears, bushings and sprockets because press cycles are fast and material yield is near total. The estimate hinges on press tonnage, tooling life and secondary operations, which this guide breaks down. **Sections:** #### Material: Grade, Density and Weight **Body:** Start with the MPIF designation the customer specifies, such as FC-0205 or FN-0205, which defines the chemistry and the property class. Part weight comes from the target density: a higher green density means more powder per part, more press tonnage and better strength. Estimate powder weight from the part volume and density target, then add a small allowance for fill variation and startup scrap. Material price changes with alloy additions and with iron powder market conditions, so quotes should carry a validity period or a material surcharge clause. Because PM wastes very little material, material often becomes the largest variable cost for heavy parts. #### Press Selection and Strokes Per Minute **Body:** Part geometry determines the press. Required tonnage comes from the projected area in the pressing direction and the compaction pressure for the target density, so a part with a large area can exclude smaller presses. Multi-level parts need multi-platen tooling and a press with enough motions. Output equals strokes per minute times parts per stroke, which drops as part height, powder fill depth and complexity rise. Estimators should hold a rate table by press and tooling family, based on observed run rates, not nameplate speed, and divide the press hourly cost by good parts per hour after setup. Setup, die change and first-piece approval can take hours, so short runs carry a heavy setup share. **Bullets:** - Projected area times compaction pressure to confirm tonnage - Number of tooling motions and levels - Observed strokes per minute by tooling family - Setup and die change hours amortized over lot size #### Sintering Furnace Cost **Body:** Parts are sintered, typically in a continuous mesh belt furnace under controlled atmosphere, so cost is driven by belt loading in kilograms per hour, furnace energy and atmosphere gas use. A light part on a belt wastes furnace capacity compared with a heavy part. Furnace cost per kilogram times part weight is a reasonable first estimate, and separate rates apply to batch or high-temperature sintering. Process data such as dimension change after sintering and carbon control matter for alloys with copper or carbon additions, since out-of-spec carbon or density creates scrap. Maintain a furnace rate per kilogram updated for energy price changes. #### Tooling Life and Secondary Operations **Body:** PM tooling is a set of die, core rods and punches in tool steel or carbide, with wear-based life measured in hundreds of thousands or millions of parts depending on the powder and geometry. Amortize cost over expected life, and add tool repair and replacement parts. Secondary operations are frequently where PM parts differ in price: sizing or coining for tolerance, machining of undercuts, cross-holes and threads, steam treating, resin or oil impregnation, heat treatment, deburring and plating. Outsourced steps add freight and minimum lot charges. Quote each as a routing step so the true unit cost reaches the customer, not just the as-sintered price. #### When PM Is Not the Right Answer **Body:** If the volume is under a few thousand pieces a year, the tooling investment rarely pays back, and machining from bar or a screw machine process may be cheaper. Parts needing very high density or complex geometry beyond a pressing capability may fit MIM or additive instead. A quote that points to the right process earns trust. Keep a simple break-even comparison by annual volume in your estimating template so the conversation with a buyer is based on arithmetic instead of habit. **Cta:** Netray can connect your quoting questions to actual press rates, scrap and furnace data in your ERP, privately and read-only, so estimates track what the floor really achieves. **Faq:** #### What drives the price of a powder metallurgy part? **Answer:** Powder weight and grade, press output in good parts per hour, furnace throughput by weight, tooling amortization and secondary operations such as sizing, machining, impregnation or heat treatment. At high volume the material share grows; at low volume setup and tooling dominate. #### How do I calculate press tonnage for a PM part? **Answer:** Multiply the projected area in the pressing direction by the compaction pressure needed for the target density, then add a margin. Multi-level parts need to be checked per level. Confirm against the press rating and tooling design with your tooling engineer, since this is a first-pass estimate only. #### Is PM cheaper than machining? **Answer:** Usually for high volumes of geometries that press well, because material use and cycle time are low. For short runs, or parts with features that need extensive secondary machining, machining can win. Compare total cost over program volume, including tooling, rather than only piece price. ## Related Slugs - manufacturing-costing-methods-comparison - erp-for-screw-machine-shops - metal-injection-molding-part-cost-tooling-amortization - finite-capacity-scheduling-guide ## Search terms powder metallurgy cost per part, press and sinter cost estimate, PM part pricing, MPIF FC-0205 cost, powder metal press tonnage, sintering furnace cost per kg, powder metallurgy vs machining --- Talk to an engineer: https://netray.co/contact?intent=erp_ai | Machine catalog: https://netray.co/agent/catalog.json