# Calibration Interval Calculator > Source: https://netray.co/tools/calibration-interval-calculator > Publisher: Netray (netray.co), AI and integration engineering for ERP and manufacturing systems. > Section: Free Tools ## Short answer Estimate a new calibration interval from the number of as-found in-tolerance results and your target reliability. ## Category quality ## Audience - Metrology manager - Quality engineer - Calibration technician ## Tool **Kind:** calculator **Inputs:** #### Current interval **Key:** current **Type:** number **Default:** 12 **Min:** 1 **Step:** 1 **Unit:** months #### Calibrations in the history **Key:** total **Type:** number **Default:** 20 **Min:** 1 **Step:** 1 **Unit:** events **Help:** Count of recent calibration events for this instrument family or model. #### Found in tolerance **Key:** in_tol **Type:** number **Default:** 17 **Min:** 0 **Step:** 1 **Unit:** events **Help:** As-found results that were within tolerance at the end of the interval. #### Reliability target **Key:** target **Type:** select **Default:** 0.85 **Options:** ##### 80% **Value:** 0.8 ##### 85% **Value:** 0.85 ##### 90% **Value:** 0.9 ##### 95% **Value:** 0.95 **Help:** Required probability that the item is still in tolerance at end of interval. **Outputs:** #### Observed reliability **Key:** obs **Expr:** 100 * in_tol / total **Format:** percent #### Unrestricted interval from exponential model **Key:** raw **Expr:** current * ln(target) / ln(clamp(in_tol / total, 0.01, 0.999)) **Format:** months **Description:** Interval at which predicted reliability equals the target. #### Recommended interval (limited to half or double) **Key:** rec **Expr:** round(clamp(raw, current * 0.5, current * 2)) **Format:** months **Primary:** true **Description:** Changes are capped so one data set cannot swing the interval too far. #### Change versus current **Key:** chg **Expr:** 100 * (rec / current - 1) **Format:** percent **Primary:** true **Chart:** #### Recommended interval vs in-tolerance count **Type:** line **X:** in_tol **From:** 8 **To:** 20 **Steps:** 13 **Series:** - rec **Disclaimer:** A simple exponential reliability model for planning. For critical or accredited work, follow your calibration procedure and the method in NCSLI RP-1 or ILAC G24, and keep management approval of interval changes. ## Content **Intro:** Most plants set calibration intervals at 12 months and never change them. That wastes money on stable gages and leaves unstable ones overdue. This calculator gives a defensible starting point from your own as-found history. **Sections:** #### How to use it **Body:** Gather the as-found results for the same instrument model or family over a number of calibration events. Count how many were in tolerance when received. Enter the current interval, the total events, the in-tolerance count and your reliability target. The tool fits a simple exponential model, in which reliability falls as exp(minus lambda times time), solves for the interval that meets the target and caps the change at half or double the current interval. Use the output as input to your review, not as an automatic change. #### Method and standards **Body:** ISO 10012 and ISO/IEC 17025 both expect that calibration intervals are based on evidence and reviewed, and ILAC G24 describes the common techniques. NCSLI RP-1 lists methods from simple response adjustments to statistical reliability models. This tool is a simplified reliability-target approach: observed end-of-period reliability sets lambda, and the target reliability sets the new interval. A larger sample gives a more trustworthy estimate, so treat results from fewer than about 10 events as indicative only. #### Common mistakes **Body:** Do not extend an interval when the history includes out-of-tolerance findings that were not investigated. Do not mix very different instruments in one count, since a gage block and a digital multimeter do not drift alike. Count only as-found data, not as-left. Account for usage: a caliper used every hour is not the same as one used monthly. Also record the impact of any out-of-tolerance finding on product shipped, because shortening the interval does not fix that exposure. **Bullets:** - Use as-found data only - Group like instruments - Document approval of every change - Investigate each out-of-tolerance event **Cta:** If your calibration due dates sit in an ERP or CMMS, Netray can help link interval reviews to that system so changes flow through automatically. **Faq:** #### What interval should a new instrument start at? **Answer:** Start with the manufacturer's recommendation, commonly 12 months for hand tools, and shorten it for harsh use or tight tolerance. Then adjust once you have several as-found results. Some labs start at 6 months for critical gages. #### How much data do I need? **Answer:** More is better. With under about 10 events a single failure moves the estimate a lot, so keep changes small. For a family of similar instruments, pool the history by model to reach a useful sample size. #### What reliability target is normal? **Answer:** Many labs use 85% to 95% depending on risk. Safety critical or high-value measurements often use 95% or more. Lower-risk shop tools may accept 80% to 85%. #### Is the interval change automatic? **Answer:** It should not be. Treat the result as a recommendation, review it with the equipment owner and have it approved under your quality system, then update the due date logic in your gage management system. ## Search terms calibration interval calculator, how to determine calibration interval, calibration interval analysis, calibration frequency calculator, extend calibration interval, NCSLI RP-1 calibration interval, ISO 10012 calibration interval, end of period reliability --- Talk to an engineer: https://netray.co/contact?intent=erp_ai | Machine catalog: https://netray.co/agent/catalog.json