# Injection Molding Clamp Tonnage Calculator

> Source: https://netray.co/tools/injection-molding-clamp-tonnage-calculator
> Publisher: Netray (netray.co), AI and integration engineering for ERP and manufacturing systems.
> Section: Free Tools

## Short answer

Estimate the clamp force a mold needs from projected area, cavity count and average cavity pressure, and see which press size fits.

## Category

industry-templates

## Industry

Plastics and Injection Molding

## Audience

- Process engineer
- Molder
- Tooling engineer
- Quoting estimator

## Tool

**Kind:** calculator

**Inputs:**

#### Projected area per cavity

**Key:** area

**Type:** number

**Default:** 100

**Min:** 1

**Step:** 5

**Unit:** cm2

**Help:** Area of the part as seen along the mold opening direction, not the surface area.

#### Number of cavities

**Key:** cavities

**Type:** number

**Default:** 4

**Min:** 1

**Step:** 1

**Unit:** cavities

#### Projected runner area per shot

**Key:** runner_area

**Type:** number

**Default:** 30

**Min:** 0

**Step:** 5

**Unit:** cm2

**Help:** Use 0 for a hot runner system. Include sprue, runners and cold slugs.

#### Average cavity pressure

**Key:** pressure

**Type:** number

**Default:** 350

**Min:** 100

**Max:** 1000

**Step:** 25

**Unit:** bar

**Help:** Typical range is 250 to 500 bar for general parts and higher for thin wall or long flow.

#### Safety factor

**Key:** safety

**Type:** select

**Default:** 1.1

**Options:**

##### 1.00 (none)

**Value:** 1

##### 1.10 (typical)

**Value:** 1.1

##### 1.20 (thin wall, high speed)

**Value:** 1.2

#### Press rated clamp

**Key:** press_tonnage

**Type:** number

**Default:** 200

**Min:** 10

**Step:** 10

**Unit:** metric tons

**Outputs:**

#### Total projected area

**Key:** total_area

**Expr:** area * cavities + runner_area

**Format:** number

**Description:** Cavity area plus runner area, in cm2.

#### Required clamp force

**Key:** force_kn

**Expr:** total_area * pressure / 100 * safety

**Format:** integer

**Description:** Kilonewtons, including the safety factor.

#### Required clamp (metric tons)

**Key:** tonnes

**Expr:** force_kn / 9.80665

**Format:** decimal

**Primary:** true

**Description:** Metric tonnes-force.

#### Required clamp (US short tons)

**Key:** us_tons

**Expr:** tonnes * 1.10231

**Format:** decimal

**Primary:** true

**Description:** US short tons-force.

#### Tons per square inch of projected area

**Key:** tsi

**Expr:** us_tons / (total_area / 6.4516)

**Format:** decimal

**Description:** Compare with the 2 to 5 tons per square inch rule of thumb.

#### Press clamp utilization

**Key:** util

**Expr:** tonnes / press_tonnage * 100

**Format:** percent

**Description:** Above about 85 percent leaves little margin for flash control.

**Chart:**

#### Required clamp (metric tons) vs cavity pressure

**Type:** line

**X:** pressure

**From:** 150

**To:** 700

**Steps:** 12

**Series:**

- tonnes

**Disclaimer:** Estimate only. Actual clamp depends on flow length, wall thickness, melt viscosity and fill speed. Confirm with mold-filling simulation or a trial on the real press.

## Content

**Intro:** Clamp tonnage is the force that keeps the mold shut against the pressure of the melt inside it. Too little and the parting line flashes; too much wastes press capacity and stresses the tool. This calculator gives a first-pass number from projected area and cavity pressure.

**Sections:**

#### How to use the calculator

**Body:** Measure the projected area of one part in the direction the mold opens, then enter the number of cavities and the projected area of the sprue and runner for a cold runner mold. Pick an average cavity pressure for the resin and wall thickness, choose a safety factor and enter the rated clamp of the press you plan to use. The result shows required force in kilonewtons, metric tons and US tons, plus how much of the press you are using.

**Bullets:**

- Projected area is a shadow, not surface area.
- Use 0 runner area for a true hot runner.
- Start at 350 bar for general purpose parts.
- Raise pressure for thin walls and long flow lengths.

#### The formula behind it

**Body:** Clamp force equals total projected area times average cavity pressure. With area in cm2 and pressure in bar, force in kN is area times pressure divided by 100. Dividing by 9.80665 gives metric tonnes-force, and multiplying that by 1.10231 gives US short tons. The common shop rule of 2 to 5 US tons per square inch of projected area is the same idea expressed per unit area, with the lower end for easy flowing resins in thick walls and the upper end for engineering grades in thin walls.

#### Reading the result

**Body:** With the defaults, four 100 cm2 cavities plus a 30 cm2 runner at 350 bar and a 1.1 factor need roughly 160 metric tons, so a 200 ton press runs near 80 percent utilization. That is workable. If utilization lands above 85 to 90 percent, consider a larger press, fewer cavities, a hot runner to remove runner area, or a lower fill pressure through gate and vent changes. The chart shows how sensitive tonnage is to cavity pressure so you can see the cost of a hard-to-fill part.

#### Common mistakes

**Body:** The most common error is using surface area instead of projected area, which overstates tonnage badly on deep parts. Others include forgetting the runner on cold runner molds, using packing pressure instead of average cavity pressure, and ignoring that a mold with side actions or lifters may need extra locking force. Also check that the mold fits between the tie bars and that the press has enough shot size, daylight and platen strength; clamp is only one of the fit checks.

**Cta:** If press and mold data live in your ERP or MES, we can set up a private assistant that checks mold-to-press fit before a job is scheduled. Ask for a short walk-through.

**Faq:**

#### How do I calculate clamp tonnage for injection molding?

**Answer:** Multiply the total projected area of all cavities and runners by the average cavity pressure, then add a safety factor of about 10 percent. With area in cm2 and pressure in bar, kN equals area times pressure divided by 100.

#### What is a good tons per square inch rule?

**Answer:** Shops often use 2 to 5 US tons per square inch of projected area. Easy flowing commodity resins in thick sections sit near 2 to 3, while engineering resins in thin walls may need 4 to 5 or more.

#### Does a hot runner reduce clamp tonnage?

**Answer:** Yes. A hot runner has no cold runner or sprue to pressurize, so projected runner area drops to zero. For small parts with a large runner footprint this can cut required clamp noticeably.

#### What happens if clamp is too low?

**Answer:** The mold can open slightly under melt pressure, causing flash at the parting line. Flash often shows first on thin-walled areas and can damage the tool steel if it continues.

## Search terms

clamp tonnage calculator, injection molding clamp force calculation, how to calculate clamp tonnage, injection molding tonnage per square inch, projected area clamp force, press size for mold, clamp tonnage formula, injection molding machine sizing

---
Talk to an engineer: https://netray.co/contact?intent=erp_ai | Machine catalog: https://netray.co/agent/catalog.json