# Injection Moulding Quality Control Checklist > Source: https://netray.co/tools/injection-moulding-quality-control-checklist > Publisher: Netray (netray.co), AI and integration engineering for ERP and manufacturing systems. > Section: Free Tools ## Short answer A printable first piece, in-process and final inspection checklist for injection molded parts with sampling and record-keeping guidance. ## Category quality ## Industry Plastics and Injection Molding ## Audience - Molding quality technician - Production supervisor - Process engineer ## Tool **Kind:** checklist **Groups:** #### Setup and first piece approval **Items:** **Text:** Work order, part revision and drawing revision match the traveler **Critical:** true **Text:** Correct mold installed and mold ID verified against the job **Critical:** true Process settings match the approved setting sheet **Text:** Material grade, lot and drying time/temperature verified **Critical:** true Hopper dryer dew point and regrind ratio within limits Mold cleaned, vents clear, no flash residue on parting line First shots purged and cavity count confirmed full **Text:** First piece measured on all drawing critical dimensions **Critical:** true Visual standard and color match checked against limit sample **Text:** First piece sign-off by quality before release to run **Critical:** true #### In-process checks **Items:** Cycle time, melt temperature, hold pressure and cushion logged at set interval Cushion stable, no drift or short shot trend **Text:** Visual check of every cavity at defined frequency for flash, sink, short shot, burn, splay, flow lines **Critical:** true Dimensional check of critical features per control plan sampling Gate vestige and degating quality within spec Insert, overmold or secondary operations checked where applicable **Text:** Rejects segregated, tagged and counted by defect code **Critical:** true Mold temperature and chiller flow verified after any stoppage **Text:** Re-approval after restart, material change or process adjustment **Critical:** true #### Final inspection and release **Items:** Sample drawn per agreed plan (for example ANSI/ASQ Z1.4 or control plan) **Text:** Critical and major characteristics measured and recorded **Critical:** true Weight check or gauge check completed **Text:** Packaging, labeling, lot traceability and quantity verified **Critical:** true Certificate of conformance or inspection report prepared where required **Text:** Nonconforming lots held and NCR raised **Critical:** true #### Records and improvement **Items:** Inspection results stored against lot, job and cavity **Text:** Gauges used are within calibration date **Critical:** true Scrap rate by defect code reviewed every shift or week Repeat defects escalated to corrective action Mold maintenance requests raised for recurring flash or wear **Scoring Note:** Tick each item at the check point it belongs to. Any critical item left open should stop release of the lot. Keep a signed copy with the job record. ## Content **Intro:** This injection moulding quality control checklist walks a molding job from first piece approval through in-process checks to final release. It follows the structure of a control plan without copying any customer form, so you can tick it, print it and file it with the job. **Sections:** #### How to use the checklist **Body:** Print one copy per job or work in the browser and export. Use the first group at setup, the second at the frequency your control plan sets (hourly is common for visual and dimensional checks), and the final group at lot release. Mark the critical items first. If a critical item fails, stop the run, quarantine product since the last good check and raise a nonconformance. #### Sampling and the method behind it **Body:** Final inspection often uses attribute sampling from ANSI/ASQ Z1.4 (the civilian successor to MIL-STD-105E) with an acceptance quality limit agreed with the customer. In-process checks are usually fixed-frequency, such as one shot per cavity every hour, plus dimensional checks on critical features. Capability studies (Cpk) on critical dimensions justify reduced sampling. Always follow the customer quality agreement over any generic plan. **Bullets:** - First piece: 100% of drawing characteristics - In-process: visual every cavity, dimensions per control plan - Final: lot sample per AQL plan or customer requirement #### Typical defects to check for **Body:** Short shots, flash, sink marks, voids, weld lines, burn marks, splay, warpage and color streaks are the usual visual rejects. Many trace to moisture, melt temperature, hold pressure or mold wear. Log every reject with a defect code so the Pareto points you to the process cause rather than the symptom. Track scrap by cavity to find a single worn or blocked cavity quickly. #### Record keeping and ERP integration **Body:** Auditors in ISO 9001, IATF 16949 and ISO 13485 plants ask for traceability: material lot to job to inspection results. Record inspections against the production order in your ERP or MES, not only on paper, so a customer complaint can be traced to a lot quickly. For on-prem plants, a private AI layer can summarize reject trends by mold and shift without exposing production data. **Cta:** If inspection results sit on paper or in separate spreadsheets, Netray can connect them to your ERP and add a private on-prem AI that answers questions about scrap by mold, shift and defect. **Faq:** #### How often should in-process inspection happen in injection molding? **Answer:** It depends on your control plan and customer. Hourly visual checks of every cavity and hourly or per-lot dimensional checks on critical features are common, with extra checks after any restart, material change or mold adjustment. #### What is first piece inspection in injection molding? **Answer:** It is a full check of the first acceptable parts after setup or change against the drawing and visual standards. Production is not released until quality signs off, which prevents running a whole lot with a setup error. #### Which sampling plan should I use for final inspection? **Answer:** Use the plan in your customer quality agreement. If none exists, ANSI/ASQ Z1.4 with an agreed AQL is a common basis. Critical features often need tighter limits or 100% inspection regardless of the AQL table. #### How do I improve injection moulding quality over time? **Answer:** Log rejects by defect code and cavity, review the Pareto weekly, tie repeat defects to corrective actions, and protect process settings with a controlled setting sheet. Preventive mold maintenance cuts flash and wear defects at the source. ## Search terms injection moulding quality control checklist, injection moulding quality checklist, injection mould inspection checklist, injection molding quality inspection, injection molding quality control, injection moulding quality improvement, molding first piece inspection checklist, plastic part inspection checklist --- Talk to an engineer: https://netray.co/contact?intent=erp_ai | Machine catalog: https://netray.co/agent/catalog.json