# Stamping Strip Layout and Material Utilization Calculator

> Source: https://netray.co/tools/stamping-strip-layout-material-utilization-calculator
> Publisher: Netray (netray.co), AI and integration engineering for ERP and manufacturing systems.
> Section: Free Tools

## Short answer

Turn blank size, bridge and edge scrap into strip width, pitch, utilization percent and material cost per part, with a sweep of utilization against bridge width.

## Category

engineering-plm

## Industry

Metal Stamping

## Audience

- Estimator
- Tool and die designer
- Manufacturing engineer

## Tool

**Kind:** calculator

**Currency:** $

**Inputs:**

#### Blank length (in feed direction)

**Key:** blank_len

**Type:** number

**Default:** 3

**Min:** 0.1

**Step:** 0.05

**Unit:** in

**Help:** Part length along the strip, measured parallel to the feed.

#### Blank width (across the strip)

**Key:** blank_wid

**Type:** number

**Default:** 2

**Min:** 0.1

**Step:** 0.05

**Unit:** in

**Help:** Part width across the strip for one lane.

#### Net part area after cutouts

**Key:** part_area

**Type:** number

**Default:** 5.2

**Min:** 0.01

**Step:** 0.05

**Unit:** in2

**Help:** Area of the finished flat blank with holes and slots removed. Take it from CAD flat pattern.

#### Bridge (web) between blanks

**Key:** bridge

**Type:** number

**Default:** 0.08

**Min:** 0

**Step:** 0.005

**Unit:** in

**Help:** Scrap web between blanks and between lanes. A common starting point is 1.0 to 1.5 times material thickness, with a practical minimum around 0.060 in.

#### Edge scrap (each side)

**Key:** edge

**Type:** number

**Default:** 0.1

**Min:** 0

**Step:** 0.005

**Unit:** in

**Help:** Carrier or edge web on each side of the strip.

#### Parts across the strip

**Key:** lanes

**Type:** select

**Default:** 1

**Options:**

##### 1 lane

**Value:** 1

##### 2 lanes

**Value:** 2

##### 3 lanes

**Value:** 3

##### 4 lanes

**Value:** 4

#### Material thickness

**Key:** thk

**Type:** number

**Default:** 0.06

**Min:** 0.005

**Step:** 0.001

**Unit:** in

#### Material

**Key:** dens

**Type:** select

**Default:** 0.284

**Options:**

##### Carbon steel (0.284 lb/in3)

**Value:** 0.284

##### Stainless 304/316 (0.289 lb/in3)

**Value:** 0.289

##### Aluminum 5052/6061 (0.098 lb/in3)

**Value:** 0.098

##### Brass C260 (0.308 lb/in3)

**Value:** 0.308

##### Copper C110 (0.322 lb/in3)

**Value:** 0.322

#### Coil price

**Key:** price

**Type:** number

**Default:** 0.55

**Min:** 0

**Step:** 0.01

**Unit:** $/lb

#### Scrap credit

**Key:** credit

**Type:** number

**Default:** 0.1

**Min:** 0

**Step:** 0.01

**Unit:** $/lb

**Help:** What the scrap hauler pays you per pound. Many shops quote on gross material and take no credit; set to 0 to do that.

**Outputs:**

#### Progression pitch

**Key:** pitch

**Expr:** blank_len + bridge

**Format:** decimal

**Description:** Feed advance per stroke in inches.

#### Strip (coil slit) width

**Key:** strip_w

**Expr:** lanes * blank_wid + (lanes - 1) * bridge + 2 * edge

**Format:** decimal

**Description:** Order the coil slit to this width plus your mill tolerance.

#### Strip area consumed per part

**Key:** area_pp

**Expr:** pitch * strip_w / lanes

**Format:** decimal

**Description:** Square inches of strip used for each finished part.

#### Material utilization

**Key:** util

**Expr:** part_area / area_pp * 100

**Format:** percent

**Primary:** true

**Description:** Net part area divided by strip area consumed. Typical progressive die jobs run 55 to 85 percent.

#### Gross weight per part

**Key:** gross_wt

**Expr:** area_pp * thk * dens

**Format:** decimal

**Description:** Pounds of coil consumed per part, including scrap.

#### Net weight per part

**Key:** net_wt

**Expr:** part_area * thk * dens

**Format:** decimal

**Description:** Pounds in the finished part.

#### Scrap weight per part

**Key:** scrap_wt

**Expr:** gross_wt - net_wt

**Format:** decimal

#### Net material cost per part

**Key:** mat_cost

**Expr:** gross_wt * price - scrap_wt * credit

**Format:** currency

**Primary:** true

**Description:** Gross material at coil price less scrap credit.

**Chart:**

#### Material utilization vs bridge width

**Type:** line

**X:** bridge

**From:** 0.03

**To:** 0.3

**Steps:** 28

**Series:**

- util

**Disclaimer:** Planning estimate. Final bridge, carrier and edge dimensions depend on material, thickness, die design and the press feed. Check with your tool designer.

## Content

**Intro:** Material is usually the largest single line in a stamping quote, and strip layout decides how much of each pound ends up in the part. This calculator turns the blank size, bridge and edge scrap into strip width, pitch, utilization and material cost per part.

**Sections:**

#### How to use the calculator

**Body:** Enter the blank length along the feed and the blank width across the strip, then the net part area from your CAD flat pattern. Set the bridge and edge scrap, pick the number of lanes and the material, and add the coil price. The strip width tells you what to order from the slitter, and the utilization number tells you how hard the layout is working. Use the chart to see how much utilization you give up for each added thousandth of bridge. A part with a large cutout can have a low utilization even with a tight layout, so also look at whether a nested second part could use the slug.

#### The formulas

**Body:** Pitch equals blank length plus bridge. Strip width equals lanes times blank width, plus (lanes minus 1) bridges, plus two edge scraps. Strip area per part equals pitch times strip width divided by lanes. Utilization equals net part area divided by strip area per part. Weight equals area times thickness times density, using 0.284 lb/in3 for carbon steel and 0.098 lb/in3 for aluminum. These are standard geometric relations, not a proprietary model, so a spreadsheet check will match.

**Bullets:**

- Units are inches, pounds and dollars per pound.
- Single-row, straight-feed layouts only; angled or tipped nests need a CAD nesting tool.
- Dimensions are nominal and ignore slit width tolerance.

#### Reading the result and common mistakes

**Body:** The usual mistake is quoting on net weight, which understates cost by the scrap fraction. Another is using the gross blank area for part area when the part has large cutouts, which overstates utilization. A third is a bridge that is too thin for the thickness; thin webs cause strip buckling, pulled slugs and feed misses. If utilization is below about 55 percent, ask whether a two-lane layout, a different orientation, or a re-sized carrier could recover material. Always confirm the final layout with the die designer before locking the price.

**Cta:** If your estimators re-key blank sizes and coil prices from the ERP into spreadsheets, we can wire this calculation to your item master and costing data. Ask for a short walkthrough.

**Faq:**

#### What material utilization is normal for stamping?

**Answer:** Simple blanking dies on rectangles can exceed 85 percent. Progressive dies with carriers, forms and large cutouts commonly land between 55 and 80 percent. Below about 50 percent, look at layout, orientation, or nesting a second part in the slug area.

#### How wide should the bridge be?

**Answer:** A common rule of thumb is 1.0 to 1.5 times material thickness, with a practical floor near 0.060 in for thin gauge. Thicker material, hard alloys and long webs need more. Treat it as a starting value and confirm it with the die designer.

#### Should I quote gross or net material?

**Answer:** Quote on gross weight at coil price, then subtract any scrap credit you actually receive. Some customers require that you pass scrap value through. Quoting on net weight alone leaves the scrap cost unrecovered.

#### Does this work for multi-lane layouts?

**Answer:** Yes for straight multi-lane layouts. Select the number of lanes and the calculator adds the inter-lane bridges to the strip width and divides the strip area per pitch by the number of parts produced per stroke.

## Search terms

strip layout calculator, material utilization stamping, blank size calculator stamping, progressive die strip layout, stamping scrap percentage, coil width calculator stamping, material yield blanking die, stamping material cost per part

---
Talk to an engineer: https://netray.co/contact?intent=erp_ai | Machine catalog: https://netray.co/agent/catalog.json